Remove the cable and Connect the battery connector to the phone and power it on. Now you successfully flashed the Fastboot ROM on your Bricked Redmi Note 5 Pro. And Your phone will reboot automatically. Once the flashing process is completed you will see the success message on the Mi Flash tool. Hit the Flash button and the flashing process will start on your phone and this will take 5 to 6 minutes to complete the process.ġ0. But we recommend you to chose the Clean all option this will not lock the bootloader of your phone.ĩ. If you want to lock the bootloader again then select the “Clean all and Lock”. Click on the “Clean all” option form bottom right corner. Now paste the URL in the Address bar of Mi Flash Tool. Now go to the Fastboot ROM folder and copy the URL of the folder.ħ. Now in the Mi Flash tool click on the Refresh Button and you will see your phone connected to the App.Ħ. Make sure your phone is connected and phone is in EDL modeĥ. Now run the Mi Flash tool app on your PC.Ĥ. Now unzip the Fastboot ROM folder on your desktop and you will see some files and images folder in the Fastboot ROM folder.ģ.
Go to your desktop and install the Mi Flash tool and you will see the Mi Flash application on your desktop.Ģ. Flash Fastboot ROM on bricked Redmi Note 5 Proġ. And you are ready to flash the Fastboot ROM on your phone. The driver will be installed Successfully and you can see added in Ports as Qualcomm HS-USB. Choose Install this Driver Software anyway.ħ.
And select the Qualcomm HS-USB QDLoader 9008 drivers that you downloaded above. Choose Browse My Computer for Driver Software.
If you see QHUSB_BULK in the device manager, Right Click and choose Update Drivers.Ħ. When PC detects new hardware, Remove Twizzer/Wire from Test Points.ĥ. Short the Test Points with Twizzer or Wire and now Connect USB to PC. Now you need a twizzer or Piece of wire to Short/connect the test points to Enter EDL mode. The test point area might be covered by tape. Disconnect the battery connector carefully from Main Board as shown in the below picture. Now use the tools/Nail to remove Back Panel. Power off the Phone and remove the SIM Card Tray. Disassemble Redmi Note 5 Pro and Boot in EDL Modeġ. After July 16/2018 Mi ID account will be added for unbreak the phone.
Go to this topic (Use Google translate) and write your Mi ID as a commentary. In order to find out your MiID, you need to go to the resource, go through the authorization and your profile Mi ID will be listed in the profile information. Please, give the Xiaomi account ID that was installed with the hard bricked device, normally it’s a 10 digits number. Submit Your Mi ID to Activate EDL on Phone Orginal USB cable to connect the phone with the PC. Download Fastboot ROM for Redmi Note 5 PRO hereĤ.
Qualcomm HS-USB QDLoader 9008 drivers, unzip the folder on the desktop.ģ. X64 (64bit) and x86 (32bit) Driver installation packages are below.2. Warning: There is always a chance of data loss and bricking a device completely when flashing customer ROM’s or performing functions at a low level, so please make sure you understand the risks before moving forward. When connecting to a Windows based computer without these drivers you will be limited to MTP (Media File Protocol) functions which is probably fine for most users, however if you want to access EDL mode (Emergency Download) and other low level ADB shell commands then installing this driver is necessary. The purpose of these drivers is to connect a phone or tablet that has a Qualcomm chipset to a Windows based computer via USB. The guide assumes that you are an administrator or have elevated privileges on a Windows machine to install programs and drivers.
How to download and install Qualcomm HS-USB QDLoader 9008 Drivers.ĭrivers can be install for modern versions of Windows 11, 10, 8.1, 8 and Windows 7 on x86 (32bit) and 圆4 (64bit) CPU architecture, please note there is no 32bit version of Windows 11 at the time of this writing.